Auto City Speedway

  • 1
Welcome

Welcome

Auto City Races are Friday & Saturday Nights-check schedule for times

Rules for the Jay 50 Race July 24th
438
4/5/2021

4/5/2021

Auto City Speedway


Rules for the Jay 50 Race July 24th

 

 

Jay 50 Memorial Rules 50]

Street Stock Rules

“Jay 50” Memorial Race

 

BASE WEIGHT

  1. a) The minimum weight before qualifying or any race is 3100 pounds including the driver. 57% left-side
weight max. All weights pre-race, race ready. Add 100 pounds for racing transmission (Bert, Brinn, Falcon, etc.)
  1. b) No Outlaw Late Model style bodies or Next Generation template bodies.
TIRES
  1. a) Hoosier F70 tire.
  2. b) Tire soaking and/or any other types of tire tampering is prohibited.
  3. c) Steel 8” racing safety wheels with 1” lug nuts.
  4. d) Tread width will be 78” measured outside side wall to side wall.
FRAME
  1. a) The minimum wheelbase is 108”. Minimum 4” frame height off the ground will be checked before
qualifying and race.
  1. b) Rear wheel drive, stock OEM clip frames only.
  2. c) Frame must utilize stock factory produced front cross members, stock factory produced side rails,
stock factory produced rear crossmember. (factory produced means “original equipment

manufacturer produced, not aftermarket)

  1. d) Wheelbase may be altered from factory length to no measurement shorter than 108?
  2. e) No tubular fabricated chassis of any kind.
  3. f) Minimum fuel cell height off the ground will be 8” which can be checked before qualifying or any
race.
  1. g) Stock OEM style gearbox; no rack and pinion steering components allowed.
  2. h) Factory suspension mounts must be retained other than the upper A-frame mounts on the front clip.
Factory mounts are to be within + or – 1? of the O.E.M. configuration.
  1. i) Tubular frame structure is allowed from the centerline of axle rearward to reinforce the fuel cell to
bumper area. 2?x3”.095 WALL minimum. This is the only tube frame modification allowed.
  1. j) Cars must be able to cross over scales without dragging.
BODY
  1. a) Body must be stock appearing from front to rear. No flat sides or stretched out
bodies. ABSOLUTELY NO OUTLAW FABRICATED TYPE BODIES. NO EXCEPTIONS.
  1. b) There will be no gaps or overlapped panels that will let air escape. Mount these panels as they were
intended to be mounted. All nose and tail pieces will be mounted in a stock fashion. Must have Tail panel

of some kind and at least half the height of the body, May not be open. Vintage steel original bodies are

encouraged.

  1. c) 6” tall spoiler X width of trunk.
  2. d) All truck bodies require a back window, a flat tonneau cover up to the top of the bed and
have minimal rake on the bed. No downforce designed truck beds.
  1. e) All Street Stocks will retain windshield posts which will be steel or fiberglass. No
wraparound windshields of any kind. No stretching the pillars out to achieve more roof or

windshield angle. Roof and windshield angles are to remain close to OEM measurements.

  1. f) No mixing and matching of car bodies from front to rear. (no car body noses and truck rears,
etc)
  1. g) Rear quarter panels must remain relatively close to that of stock body
measurements. No manipulation of the right-side quarter panel shelf. right and left

quarter panels must be symmetrical at c pillar.

  1. h) No cars or trucks will have any extra rake built into their bodies from front to rear.
  2. i) No body panel or nose piece will be lower than 4” off the ground (measured with driver in
the car).
  1. j) Rub rails are allowed with no sharp edges or fasteners.
SHOCKS AND SUSPENSION
  1. a) No bump stops of any kind. Minimum 5” coil springs all 4 corners.
  2. b) Rear trailing arms can be OEM or manufactured. Adjustable heims are permissible; however,
the frame mounts and the rear end mounts will remain stock and in stock location. All trailing

arm lengths must be within 1” of a stock OEM trailing arm for that car.

  1. c) All remaining suspension parts will remain stock, be in the stock location and be mounted in
the stock angle with the exception of the front shocks which can be mounted outboard. Aftermarket center

link allowed.

  1. d) Rear springs and shocks must be stock appearing and in stock location.
  2. e) Heim ends are allowed only on shock ends, rear trailing arms and in place of front tie rod
ends.
  1. f) Sway bars must remain stock (no splined sway bars) but may be mounted above or below the
control arms. Threaded rod adjustments on the A-frame are permissible.
  1. g) Rear and/or front load bolts (screw jacks) are allowable.
  2. h) Aftermarket tubular upper A-Frames are allowed. A-frames will have stock type ball joints
(no monoballs). Upper A-Frame mounts may be modified and be within 1” of the stock

location.

  1. i) All shocks will be steel and non-adjustable. No canister shocks of any kind. No bump stops
of any kind. No Schrader valves of any kind.
  1. j) No coil binding.
  2. k) No three link rear suspensions. No panhard, j-bar, watts linkage, track bar, lift bar/arm
or any other suspension allowed other than factory converging 4 link type or leaf spring.
  1. l) No strut arm type front suspensions.
  2. m) Tech may remove a shock at any time to inspect for internal bump stops or bump springs.
  3. n) Front and rear spring pockets may be modified in the stock frame rails and stock cross
member for screw jacks. (jack plates, spring height location. must retain factory rear cross

member. height of jack plate may be adjusted. Factory rear spring pockets must remain and

in stock location.) A 2"x 4" or equivalent steel brace may be used as additional support or in

lieu of weak rear cross member with Race Director approval.

ENGINES/DRIVE TRAIN

  1. a) Engines must be stock appearing, all cast iron block and heads. Forward most spark plug MUST be in
line or ahead of upper ball joint center line.
  1. b) Cast iron or aluminum intake.
  2. c) Cast iron exhausts manifolds or headers are allowed with 3” maximum exhaust tubing.
  3. d) The carburetor will be a single 2 or 4 barrel with a maximum 1” store bought adapter or spacer.
  4. e) HEI style ignition or MSD style ignition permissible. No Traction Control Devices allowed.
  5. f) OEM automatic or standard transmission.
  6. g) Racing transmissions are allowed. Add 100 pounds for racing transmission (Bert, Brinn, Falcon, etc.)
  7. h) Minimum clutch size will be 7¼”. A 2” inspection hole must be cut in all bell housings so
the clutch can be easily seen.
  1. i) Stock style OEM rear ends only; four link or leaf suspension only.
  2. j) A steel 9” Ford is permissible with 4 link mount or leaf mount.
  3. k) No quick-change rear ends or aluminum rear end components of any kind.
  4. l) Full steel spool, steel mini spool or welded rear ends only, no limited slip differentials.
Active Gleason Torsen Differentials or equivalents are not allowed.

BRAKES

  1. a) Aftermarket brake pedals and or master cylinders are allowed.
  2. b) Aftermarket brake calipers are allowed. As well as rear disk brakes.
COCKPIT
  1. a) The full floorboard and front firewall may remain stock or be fabricated.
  2. b) A fabricated foot box must have sides and bottom that are a minimum thickness of1/8”
steel. No thin gauge sheet metal footboxes will be allowed.
  1. c) The passenger side sheet metal/floorboard will remain low next to the driver going over to the right
side frame rail.
  1. d) An aftermarket gas pedal is highly recommended.
  2. e) The main driver’s hoop and door bar construction of the roll cage will be .095 wall
thickness minimum. It will have driver’s side door plate reinforcement on the door bars welded in place.

FUEL CELL

  1. a) Fuel cells are mandatory with an 8” minimum ground clearance.
  2. b) A fuel cell guard behind the cell with two forward braces is required. Any plating of the frame around
the fuel cell is permissible.
  1. c) Stock rear frame rails may be replaced from behind the spring pockets rearward to the bumper with
2” x 3” steel tubing

Street Stock Rules

“Jay 50” Memorial Race

 

BASE WEIGHT

  1. a) The minimum weight before qualifying or any race is 3100 pounds including the driver. 57% left-side
weight max. All weights pre-race, race ready. Add 100 pounds for racing transmission (Bert, Brinn, Falcon, etc.)
  1. b) No Outlaw Late Model style bodies or Next Generation template bodies.
TIRES
  1. a) Hoosier F70 tire.
  2. b) Tire soaking and/or any other types of tire tampering is prohibited.
  3. c) Steel 8” racing safety wheels with 1” lug nuts.
  4. d) Tread width will be 78” measured outside side wall to side wall.
FRAME
  1. a) The minimum wheelbase is 108”. Minimum 4” frame height off the ground will be checked before
qualifying and race.
  1. b) Rear wheel drive, stock OEM clip frames only.
  2. c) Frame must utilize stock factory produced front cross members, stock factory produced side rails,
stock factory produced rear crossmember. (factory produced means “original equipment

manufacturer produced, not aftermarket)

  1. d) Wheelbase may be altered from factory length to no measurement shorter than 108?
  2. e) No tubular fabricated chassis of any kind.
  3. f) Minimum fuel cell height off the ground will be 8” which can be checked before qualifying or any
race.
  1. g) Stock OEM style gearbox; no rack and pinion steering components allowed.
  2. h) Factory suspension mounts must be retained other than the upper A-frame mounts on the front clip.
Factory mounts are to be within + or – 1? of the O.E.M. configuration.
  1. i) Tubular frame structure is allowed from the centerline of axle rearward to reinforce the fuel cell to
bumper area. 2?x3”.095 WALL minimum. This is the only tube frame modification allowed.
  1. j) Cars must be able to cross over scales without dragging.
BODY
  1. a) Body must be stock appearing from front to rear. No flat sides or stretched out
bodies. ABSOLUTELY NO OUTLAW FABRICATED TYPE BODIES. NO EXCEPTIONS.
  1. b) There will be no gaps or overlapped panels that will let air escape. Mount these panels as they were
intended to be mounted. All nose and tail pieces will be mounted in a stock fashion. Must have Tail panel

of some kind and at least half the height of the body, May not be open. Vintage steel original bodies are

encouraged.

  1. c) 6” tall spoiler X width of trunk.
  2. d) All truck bodies require a back window, a flat tonneau cover up to the top of the bed and
have minimal rake on the bed. No downforce designed truck beds.
  1. e) All Street Stocks will retain windshield posts which will be steel or fiberglass. No
wraparound windshields of any kind. No stretching the pillars out to achieve more roof or

windshield angle. Roof and windshield angles are to remain close to OEM measurements.

  1. f) No mixing and matching of car bodies from front to rear. (no car body noses and truck rears,
etc)
  1. g) Rear quarter panels must remain relatively close to that of stock body
measurements. No manipulation of the right-side quarter panel shelf. right and left

quarter panels must be symmetrical at c pillar.

  1. h) No cars or trucks will have any extra rake built into their bodies from front to rear.
  2. i) No body panel or nose piece will be lower than 4” off the ground (measured with driver in
the car).
  1. j) Rub rails are allowed with no sharp edges or fasteners.
SHOCKS AND SUSPENSION
  1. a) No bump stops of any kind. Minimum 5” coil springs all 4 corners.
  2. b) Rear trailing arms can be OEM or manufactured. Adjustable heims are permissible; however,
the frame mounts and the rear end mounts will remain stock and in stock location. All trailing

arm lengths must be within 1” of a stock OEM trailing arm for that car.

  1. c) All remaining suspension parts will remain stock, be in the stock location and be mounted in
the stock angle with the exception of the front shocks which can be mounted outboard. Aftermarket center

link allowed.

  1. d) Rear springs and shocks must be stock appearing and in stock location.
  2. e) Heim ends are allowed only on shock ends, rear trailing arms and in place of front tie rod
ends.
  1. f) Sway bars must remain stock (no splined sway bars) but may be mounted above or below the
control arms. Threaded rod adjustments on the A-frame are permissible.
  1. g) Rear and/or front load bolts (screw jacks) are allowable.
  2. h) Aftermarket tubular upper A-Frames are allowed. A-frames will have stock type ball joints
(no monoballs). Upper A-Frame mounts may be modified and be within 1” of the stock

location.

  1. i) All shocks will be steel and non-adjustable. No canister shocks of any kind. No bump stops
of any kind. No Schrader valves of any kind.
  1. j) No coil binding.
  2. k) No three link rear suspensions. No panhard, j-bar, watts linkage, track bar, lift bar/arm
or any other suspension allowed other than factory converging 4 link type or leaf spring.
  1. l) No strut arm type front suspensions.
  2. m) Tech may remove a shock at any time to inspect for internal bump stops or bump springs.
  3. n) Front and rear spring pockets may be modified in the stock frame rails and stock cross
member for screw jacks. (jack plates, spring height location. must retain factory rear cross

member. height of jack plate may be adjusted. Factory rear spring pockets must remain and

in stock location.) A 2"x 4" or equivalent steel brace may be used as additional support or in

lieu of weak rear cross member with Race Director approval.

ENGINES/DRIVE TRAIN

  1. a) Engines must be stock appearing, all cast iron block and heads. Forward most spark plug MUST be in
line or ahead of upper ball joint center line.
  1. b) Cast iron or aluminum intake.
  2. c) Cast iron exhausts manifolds or headers are allowed with 3” maximum exhaust tubing.
  3. d) The carburetor will be a single 2 or 4 barrel with a maximum 1” store bought adapter or spacer.
  4. e) HEI style ignition or MSD style ignition permissible. No Traction Control Devices allowed.
  5. f) OEM automatic or standard transmission.
  6. g) Racing transmissions are allowed. Add 100 pounds for racing transmission (Bert, Brinn, Falcon, etc.)
  7. h) Minimum clutch size will be 7¼”. A 2” inspection hole must be cut in all bell housings so
the clutch can be easily seen.
  1. i) Stock style OEM rear ends only; four link or leaf suspension only.
  2. j) A steel 9” Ford is permissible with 4 link mount or leaf mount.
  3. k) No quick-change rear ends or aluminum rear end components of any kind.
  4. l) Full steel spool, steel mini spool or welded rear ends only, no limited slip differentials.
Active Gleason Torsen Differentials or equivalents are not allowed.

BRAKES

  1. a) Aftermarket brake pedals and or master cylinders are allowed.
  2. b) Aftermarket brake calipers are allowed. As well as rear disk brakes.
COCKPIT
  1. a) The full floorboard and front firewall may remain stock or be fabricated.
  2. b) A fabricated foot box must have sides and bottom that are a minimum thickness of1/8”
steel. No thin gauge sheet metal footboxes will be allowed.
  1. c) The passenger side sheet metal/floorboard will remain low next to the driver going over to the right
side frame rail.
  1. d) An aftermarket gas pedal is highly recommended.
  2. e) The main driver’s hoop and door bar construction of the roll cage will be .095 wall
thickness minimum. It will have driver’s side door plate reinforcement on the door bars welded in place.

FUEL CELL

  1. a) Fuel cells are mandatory with an 8” minimum ground clearance.
  2. b) A fuel cell guard behind the cell with two forward braces is required. Any plating of the frame around
the fuel cell is permissible.
  1. c) Stock rear frame rails may be replaced from behind the spring pockets rearward to the bumper with
2” x 3” steel tubing Back to News

Latest Photos

Latest Videos

Auto City Speedway Stampede June, 2023 30 seconds
2023 30 second generic flashing date FRIDAY
2023 30 second generic flashing date SATURDAY
2023 30 second generic flashing date SATURDAY
2023 30 second generic flashing date SATURDAY
Allstar Performance
American Racer
ARP
Bob Kerns
CK 105
Dr Pepper
ELGA
Engine Pro
Five Star Bodies
GFS
GM UAW
Holley
Miller Lite
MI Super Moto
MSD Ignitions
MSPA
Mufflerman
Octane
Oguinn
PHM
Rislone
RJS
Rock Auto
Safety Solutions
Sunoco
The Herald
Tiger
Top Speed
Winters
WTRX
Xtreme